CONTROL
Controllers and sensors.
TR8
Remote control.
Radio transmitter at 433,92 Mhz rolling-code and infrared with 8 keys in silicone rubber backlit in blue, powered at 6V by two button batteries. The transmitter is equipped with support for fastening to the wall.
USA2
Connection and synchronization unit
Control unit that synchronizes and controls the simultaneous function of 2 actuators mod. C30, C40, ACK4 installed on the large same window frame. Its operation ensures that the window opens and closes with regular, uniform movement along its entire width, ensuring the safety of the window and motors applied. The USA microprocessor verifies in real time the power, current absorption and actuator speed, and ascertains that every part of the machines is functioning perfectly and regularly.
If only one of the parameters controlled does not meet the regular standard, the control unit automatic cuts off power and signals, with a signal light, the motor causing the malfunction. Only specially prepared actuators can be connected to the USA2 unit (version with 5-wire cable).
The unit and actuators function in two versions: at 230V~50Hz, or at 24V DC. Preparation for connection of all service control units for wind/rain, air conditions, smoke and heat exhaust. The device is CE marked .
TF24R_TF44R
Control and power unit
The TF24R control units (output voltage 24V DC) and TF44R (output voltage 230V) are suitable to power and control motor in low voltage or at 230V. 433.92 Mhz rolling-code radio receiver incorporated. Input for wind sensor RW and rain sensor RD12V. The device is CE marked .
RW
TR8
Remote control.
Radio transmitter at 433,92 Mhz rolling-code and infrared with 8 keys in silicone rubber backlit in blue, powered at 6V by two button batteries. The transmitter is equipped with support for fastening to the wall.
USA2
Connection and synchronization unit
Control unit that synchronizes and controls the simultaneous function of 2 actuators mod. C30, C40, ACK4 installed on the large same window frame. Its operation ensures that the window opens and closes with regular, uniform movement along its entire width, ensuring the safety of the window and motors applied. The USA microprocessor verifies in real time the power, current absorption and actuator speed, and ascertains that every part of the machines is functioning perfectly and regularly.
If only one of the parameters controlled does not meet the regular standard, the control unit automatic cuts off power and signals, with a signal light, the motor causing the malfunction. Only specially prepared actuators can be connected to the USA2 unit (version with 5-wire cable).
The unit and actuators function in two versions: at 230V~50Hz, or at 24V DC. Preparation for connection of all service control units for wind/rain, air conditions, smoke and heat exhaust. The device is CE marked .
TF24R_TF44R
Control and power unit
The TF24R control units (output voltage 24V DC) and TF44R (output voltage 230V) are suitable to power and control motor in low voltage or at 230V. 433.92 Mhz rolling-code radio receiver incorporated. Input for wind sensor RW and rain sensor RD12V. The device is CE marked .
TF33R
Control and power unit
The TF33R control unit is suitable to power and control up to 3 motors in low voltage, with forward/backward motion in automatic or “deadman” mode. Every motor is enabled with the ammeter control function, relative to mechanical force, that intervenes to stop the motor in case of malfunction such as breakage, block, etc.
A 230V motor can be controlled with the addition of a special board. Separate inputs for opening and closure of the three motors. 433.92 Mhz rolling-code radio receiver or infrared receiver incorporated. The radio control device can control the motors in open-close mode separately or in step-step mode. Input for wind sensor RW with adjustment of the threshold via trimmer. Possibility to manage two rain sensors RD 12V at the same time. Three blue leds provide signaling functions on the status of the control unit and programming of radio controls. Possibility of emergency opening and closure using the keys used to memorize the radio commands or by means of the transmitter.
Settings for control unit functions (exclusion of rain sensor, deadman function, connection to thermostat, etc.) via dipswitch. The device is marked with the CE seal
Control and power unit
The TF33R control unit is suitable to power and control up to 3 motors in low voltage, with forward/backward motion in automatic or “deadman” mode. Every motor is enabled with the ammeter control function, relative to mechanical force, that intervenes to stop the motor in case of malfunction such as breakage, block, etc.
A 230V motor can be controlled with the addition of a special board. Separate inputs for opening and closure of the three motors. 433.92 Mhz rolling-code radio receiver or infrared receiver incorporated. The radio control device can control the motors in open-close mode separately or in step-step mode. Input for wind sensor RW with adjustment of the threshold via trimmer. Possibility to manage two rain sensors RD 12V at the same time. Three blue leds provide signaling functions on the status of the control unit and programming of radio controls. Possibility of emergency opening and closure using the keys used to memorize the radio commands or by means of the transmitter.
Settings for control unit functions (exclusion of rain sensor, deadman function, connection to thermostat, etc.) via dipswitch. The device is marked with the CE seal
RW
Wind Sensor
The wind sensor is a device that, when connected to the TOPP control units, controls the automatic closure of the windows when the wind speed exceeds a preset value. It consists of a sturdy, weather-resistant plastic structure with a system of rotating blades that measure the wind speed.
RD/12
The wind sensor is a device that, when connected to the TOPP control units, controls the automatic closure of the windows when the wind speed exceeds a preset value. It consists of a sturdy, weather-resistant plastic structure with a system of rotating blades that measure the wind speed.
RD/12
Rain Sensor
The rain sensor is a device that, like the wind sensor, must be installed in the open where it can be struck by rainfall. RD/12V can be connected to TF24R, TF44R and TF33R units.They control automatic closure of the windows when the sensor detects raindrops; the sensor does not react to dew or humidity.
The rain sensor is a device that, like the wind sensor, must be installed in the open where it can be struck by rainfall. RD/12V can be connected to TF24R, TF44R and TF33R units.They control automatic closure of the windows when the sensor detects raindrops; the sensor does not react to dew or humidity.
